
Products
Dosing Equipment
-
Calibration sheet for Huwa-San
A calibration routine to ensure accurate dosing of Huwa-San using the Select doser.
Calibration sheet for Huwa-San (PDF) -
Calibration sheet for Select dosers
100CA00
This sheet and the protocol described can be used to calibrate any Select doser. Use in conjunction with a measuring cylinder (can be supplied by Dosing Solutions).
Calibration sheet for Select dosers (PDF) -
Horticulture
Select dosers are being used to dose water cleaning products into the water lines in nurseries and glass houses.
Below are English and Spanish versions of videos explaining the techniques.
-
pH and ORP Equipment
Equipment for the sensing, alerting and dosing correction of all situations where pH and ORP need to be controlled. This is particularly the case where chlorine is being used as a cleaning agent.
pH Monitor data sheet (PDF) ORP Monitor (PDF) pH Monitor IFU Aug 20 (PDF) 640 pH IFU v4 (PDF) -
Select-380 Doser
The high pressure Select Doser for water treatment.
This versatile doser can be used as a proportional doser taking a pulse from a standard water meter, or pulses from standard Dosing Solutions flow sensors. Dosing into line pressures of up to 5 bar (70 psi), it is the ideal doser for water treatment.
This is the upgrade version of the Select-360. All of the normal dosing options and ratios are easy to select on-screen as will all other dosers from Dosing Solutions Ltd.
Select-380 IFU.2 (PDF) Select-380 Data Sheet (PDF)Orange tube load from David Welch on Vimeo.
-
Select-380 T-Auto
380CA75
An auto-dosing pump that can be set at any pumping rate from 0 - 4.7 l/hr of dosed product.
380 T-Auto IFU (PDF) 380 T-Auto Technical Data (PDF) -
Select-382 Split Tandem Doser
This version of the 380 doser allows for two different products to be pumped at differing ratios. One of the pumps can be slowed so as to act at a smaller dosing ratio compared with the other.
382 Split Tandem Technical Data (PDF) Select-382 Split Tandem IFU (PDF) -
Select-382 Tandem Doser
This version of the 380 doser allows for a single product to be pumped at twice the normal rate, or for two different products to be pumped at the same dosing ratio.
One of the pumps can be slowed to account for any difference in viscosity between the two pumped products.
382 Technical Data (PDF) -
Select-388 Doser
This is the ideal doser to use for water treatment when water line pressures are relatively high, the dosed product requirement is low, and two different chemicals are being dosed at different ratios. Ideal for dosing water cleaning products as well as acidification products.
Select 388 Data Sheet (PDF) 388 IFU (PDF)Orange tube load from David Welch on Vimeo.
-
Select-390
390CA00
This is the Select-380 doser with Tx incorporated within the enclosure. Great for dosing water cleaning products with the extra benefit of receiving critical water flow information to your phone or online.
Select-390 Data Sheet.1 (PDF) -
Select-480 Doser NO LONGER AVAILABLE
The classic Select Doser. With many thousands sold all over the world, this is the doser that has defined computer controlled proportional peristaltic dosing.
Able to deliver micro-litres as well as flow rates up to 15 litres per hour, this doser can be a proportional doser, a single shot doser, a pH doser or even an AutoDoser.
The Select-480 is being withdrawn due to difficulties is sourcing component parts. The replacement Select-485 will be available shortly, or please consider the Select-640.
480 IFU (PDF) 480 Technical Data (PDF) -
Select-502/6.8
502CA00
A large output proportional doser using a diaphragm pump delivering up to 7 bar pressure.
Select-502/6.8 IFU (PDF) Select-502/6.8 PDS (PDF) -
Select-640 Autodoser
This format of doser allows for pumping of product at a specific rate. For example, if a waterline has a known flow rate as from a ground water pump, it may be possible to determine the rate at which the Select doser adds product to the line. No flow sensor is needed in this case.
Select 640 Autodoser (PDF) -
Select-640 Doser - proportional doser
This heavy-duty intelligent doser is basically a computer controlled peristaltic pump. Depending on how it is programmed it can be a proportional doser adding products such as disinfectants, vaccines, medications or vitamins to water flows. It can also be a single shot doser dispensing specific quantities of liquids as required.
If you need a product to be dosed at a rate of x ml/hr, the Select-640 can be programmed as an AutoDoser.
However, if you want to pump a specific amount (1 litre, 120ml etc.) you need the Select-640 SSD (Single Shot Doser).
640 Technical Data (PDF) Select 640 Livestock IFU (PDF) 640 IFU (Español) (PDF) Select-640 proportional IFU 20.8 (PDF)Dosed product from David Welch on Vimeo.
-
Select-640 SSD (Single Shot Doser)
The Select-640 SSD, including the VariSpeed version, dispenses a specific amount of product when activated with a single impulse.
The impulse can come from a computer generated source, or from (more normally) a single push of a foot switch.
With the VariSpeed version, on-screen controls let you specify the speed of pumping (see video).
Select-640 SSD IFU (PDF) Select-640 SSD IFU (PDF)640-SSD Vari from David Welch on Vimeo.
-
Select-640 Timed SSD
A doser that can deliver an initial dose on power-up, and then dose x ml each y minutes. Users can change the x and y values.
640-SSDIP IFU (PDF) -
Select-642 Split Tandem
010CA60
A double headed proportional doser. One side doses at the required ratio, the other side doses at a set percentage of the first side.
Select-642 Split Tandem IFU (PDF) -
Select-642 Tandem Doser
This version of the 640 doser allows for a single product to be pumped at twice the normal rate, or for two different products to be pumped at the same dosing ratio.
One of the pumps can be slowed to account for any difference in viscosity between the two pumped products.
-
Select-648 Tandem doser
Double headed doser with independent control for each side. Two different products can be dosed at completely different ratios.
Select-648 data sheet (PDF) Select-648 Instructions for Use (PDF) -
Select-650 doser with Tx
010CA65
This version of the Select-640 has the Tx communications system built into the enclosure.
Without any additional connections the Select-650 will send water consumption data to the user to indicate possible health issues, and raise Alerts if unforeseen high water flows occur.
In most areas, a GSM signal will be picked up using the built-in antenna. An external antenna can be attached if required.
For the normal dosing functions - see the Select-640 proportional doser data sheet.
Select-650 Data Sheet (PDF) Adddendum ref Tx (PDF) -
Select-G5 Doser
The high pressure Select Doser.
This doser can be adapted to be a proportional doser, an AutoDoser or a single shot doser - but crucially can dose into water line pressure up to 7 bar (100psi).
G5 IFU (PDF) G5 Technical Data (PDF) G5 Livestock IFU (PDF) G5 Livestock Technical Data (PDF) -
Select Water Meter
170CAxx
The Select Water Meter monitors water flows and displays both the current litre per hour rate (gallons per hour in USA), and the accumulating water total. The total can be easily zeroed for convenient daily total records to be taken.
Select Water Meter IFU (PDF) -
Water meter with Select-380 doser
How to read a K = 10 water meter and its connection to a Select-380 doser.
K=10 Water Meter from David Welch on Vimeo.
Stirring Equipment
-
Spinstir range
If you are dosing powder products, the powder can settle at the bottom of the stock container leading to inaccurate dosing and a waste of expensive product.
Two sizes of Spinstir are available. The 10-Series (10-12) for stirring up to 100 litres, and the 15-series (15-12) for stirring up to 200 litres.
See the data sheet for Item Numbers. Different Item Numbers are allocated according to the style of stirrer and the method of connection to a power source.
Spinstir 10-12 (PDF)
Flow Sensors
-
Mag6020
MFS6020
The Mag6020 is a flow sensor to measure extremely low water flows down to 2 l/hr (33 ml/min). This is especially useful for trials sites and small numbers of outside livestock units. Can be used with any Select doser.
-
MFS Magnetic Flow Sensor
160CA24
This flow sensor can be used with any Select Doser. If the water you are dosing into is contaminated with particles or debris, you may be advised to use this sensor.
WARNING - Do not allow this flow sensor to run dry. Inadvertent dosing may occur which could be hazardous.
This is the most advanced sensor available today. There is no turbine in the sensor - the water flows through an open tube.
Water flows up to 18,000 l/hr.
MagFlo data sheet (PDF) -
Select Keypad
160CA30
The Select Keypad is an input device to tell a Select doser how many Units are to be accounted for. The Select doser will then dose on a ml / Unit basis.
Select Keypad (PDF) -
TBR 10 Flow Sensor NO LONGER AVAILABLE
160CA07
DISCONTINUED
This flow sensor can be used with any Select Doser.
The smallest flow sensor, this one can work with water flows of 3 to 300 l/hr.
TBR10 Flow Sensor Technical Data (PDF) -
VTH25 Flow Sensor
160CA05
This flow sensor can be used with any Select Doser.
This sensor has a 1.25" thread and can operate with water flows up to 10,000 l/hr.
VTH25 Flow Sensor Technical Data (PDF) VTH25 parts assembly (PDF) -
VTH40 Flow Sensor
160CA08
This flow sensor can be used with any Select Doser.
The VTH40 is a robust brass flow sensor that has a maximum water flow rate capacity of 25,000 l/hr. It has a 2" thread.
VTH40 Flow Sensor Technical Data (PDF) -
VTY10 Flow Sensor
160CA03
This flow sensor can be used with any Select Doser.
This is the most frequently used flow sensor. It has a 3/4" thread and can work with a water flow range of 20 to 1,500 l/hr.
VTY10 Flow Sensor Technical Data (PDF) -
VTY20 flow sensor
160CA20
This flow sensor can be used with any Select Doser.
This sensor has a 1" thread and can operate with water flows up to 3,600 l/hr.
VTY20 Data Sheet (PDF)
Tx
- Level
-
Tx
A new way to get vital data on livestock health.
The Tx box collects water flow data and sends a Daily Report to the user's mobile phone with a 4-day comparison. A drop in water consumption can signify an approaching health problem.
Tx Data Sheet (PDF) Addendum for Select-650 (PDF) Tx Usage Scenarios (PDF) Tx IFUv14 130820 (PDF)
Parts
-
380 Roller Assembly - Black
330CA40
Replacement roller assembly - Black - for the Select 380.
-
380 Roller Assembly - White
330CA30
Replacement roller assembly - White - for the Select 380.
-
380 Tube Housing cover
350CA20
Plastic pump head lid cover for the Select 380.
-
480 Motor/encoder/gearbox NO LONGER AVAILABLE
165CA00
Select-480 motor / encoder / gearbox DISCONTINUED
-
480 Pump head
165CA03
Select-480 pump head without roller assembly.
-
480 Pump head lid/cover
165CA84
Clear plastic Select 480 pump head lid/cover only.
-
480 Pump head & roller
165CA01
Select-480 pump head and rollers.
-
480 Roller assembly
165CA02
Select-480 roller assembly for pump head.
-
480 Springs for roller
165CA05
Springs which are fitted into 480 roller assembly.
-
640 hall lead (plaited)
015CA20
Hall effect lead with magnet sensor.
-
640 Magnet holder/encoder
015CA15
The magnet encoder plate for the Select-640 that fits under the roller assembly.
-
640 Motor / Gearbox
015CA00
Motor/encoder/gearbox for Select-640.
-
640 Power supply 5A
019CA05
5A 12V DC power supply for the Select-640 and Select-380.
-
640 Pump head cover/lid
015CA13
The pumphead cover/lid only for the Select 640 - including the three screws and washers.
-
640 Pump head & lid only, no rollers
015CA11
Select-640 pump head and lid only, no roller assembly. With hall effect attachment included.
-
640 Pump head & roller assembly
015CA12
Select-640 pump head, lid and roller assembly with hall effect attachment included.
-
640 Roller assembly
015CA10
The roller assembly used in all Select-640 dosers.
-
Battery clips & leads with plug to doser
169CA47
Battery clips and leads for Select-480/640 dosers.
-
DC cable & socket
164CA00
For use as a replacement inside Select doser. dc cable and socket
-
Delivery tube 30m
155CA48
Roll of 30m delivery tube 4.8mm id
-
Delivery tube 3m
152CA05
Delivery tube (3m length) plus end weight (as despatched with dosers).
-
Eeprom
190CA15
Computer chip containing dosing ratio information.
-
Enclosure base for Select 480/640
157CA00
Enclosure base only.
-
Enclosure lid for Select 480/640
157CA50
Enclosure lid only, with the 4 plastic screws.
-
EPDM Black injection valve
015CA18
Alternate non-return injection assembly for dosers.
-
Fascia label
165CA81
Fascia label for Select 480/640
-
Foot switch for SSD
305CA00
Foot switch for all Select SSD models.
-
G5 Additional standard pump-head
369CA#7
An additional G5 pump-head for use with the G5 high pressure pump single head drive shaft. 369CA followed by the tube number to be factory fitted. eg. 369CA#7
-
G5 Delivery tube (6m)
385CA27
Polythene delivery tube (6m) to use with the G5 system.
-
G5 Duckbill NRV insert - replacement
385CA25
Used inside the G5 injection assembly to prevent backflow of water.
-
G5 Easy Fit Latching Clip
385CA42
Latching clip used to fasten pump head lid to the pump head.
-
G5 EasyFit Pump Head Housing
385CA44
EasyFit G5 pump-head housing.
-
G5 EasyFit Pump Head Lid/Cover
385CA43
EasyFit pump head cover which is also used as a wrench tool.
-
G5 EasyFit roller assembly
385CA45
G5 EasyFit roller assembly.
-
G5 End weight assembly - replacement
385CA23
To be used on the suction end of the G5 delivery tube. Has course filter and is weighted with ceramic.
-
G5 Extension drive shaft for double pump-head
370CA50
Drive shaft can be easily fitted to allow for 2 pump-heads to be used with the G5 system
-
G5 Extension pump-head
370CA#2
Extension pump-head to be used on the extension drive shaft to allow 2 pump-heads to be used. The extension pump head to be fitted closest to the motor. Item number is 370CA followed by the tube number to be factory fitted.
-
G5 Ferrule (blue)
385CA21
Ferrule to be used on delivery tube inside the lock nut.
-
G5 Gear & washer
385CA31
G5 gear and washer for use inside motor.
-
G5 Hall loom & tube burst
385CA26
G5 hall loom & tube burst. For use as a replacement for Select-G5.
-
G5 Injection assembly - replacement
385CA24
Injection assembly contains non-return duckbill. 1/2 inch thread.
-
G5 Locking nuts
385CA22
Lock nuts used to keep ferrules in place and to fix the delivery tube to the pump tube, and injection assembly.
-
G5 Polythene delivery tube 30m
385CA29
Roll of 30m polythene delivery tube for G5
-
G5 Replacement pump tube #1
380CA#1
Replacement pump tube #1 for the G5 system. Sold individually.
-
G5 Replacement pump tube#7
380CA#7
Replacement pump tube #7 for the G5 system. Sold individually.
-
G5 Roller assembly - replacement
385CA28
To be used in the G5 pump-head as a replacement after damage.
-
G5 Stenner EasyFit Fan Brake Tool
385CA41
Fan brake tool used to prevent the motor from turning during pump tube replacement in the Select-G5.
-
G5 Stenner EasyFit Pump Head
385CA48
EasyFit pump head for the Select-G5. Roller assembly not included. Pump tube not included.
-
G5 Stenner EasyFit Pump Head & rollers
385CA40
EasyFit pump head complete with roller assembly for the Select-G5. Pump tube not included
-
G5 Tube housing cover with bushing
385CA30
G5 pump head lid cover.
-
Injection assembly (female)
153CA10
Female injection assembly only. 3/8" thread.
-
Injection assembly (male)
153CA20
Barbed connection to PVC delivery tube from doser.
-
Injection assembly (M/F)
153CA02
Acid resistant grey male and female coupling.
Injector has a 3/8" male thread.
-
Magnetic Flow Sensor (MFS)
160CA24
Pipe sizes: 8mm / 14 mm/ 18 mm / 25 mm Max Flows: 8 mm - 1,500 l/hr 14 mm - 3,600 l/hr 18 mm - 14,400 l/hr 25 mm - 18,000 l/hr
There is no turbine in this sensor - the water flows through an open tube.
-
Non-return valve
156CA00
For delivery line (4.8mm id) non return valve check
-
Parallel connection lead
166CA90
Parallel connection lead
To connect up to 25 Select dosers in parallel using a single flow sensor.
-
PCB
165CA09
Printed circuit board for Select dosers.
-
pH 4.0 buffer solution - bottle
720CA14
Buffer solution pH 4.0 460ml bottle
-
pH 4.0 buffer solution - sachet
720CA04
Buffer solution pH 4.0 25ml sachet
-
pH 7.0 buffer solution - bottle
720CA17
Buffer solution pH 7.0 460ml bottle
-
pH 7.0 buffer solution - sachet
720CA07
Buffer solution pH 7.0 25ml sachet
-
pH Electrode
710CA00
pH electrode for pH dosers. Lead length 1m.
-
PIC
190CA20
Computer chip containing the operating program for dosers.
-
Plastic enclosure screw
174CA00
Plastic enclosure screw for lid of Select 480/640. 1 screw.
-
Power supply 12V-DC 1.0A
169CA00
Power supply 12V-DC 1.0 A
For use with the Select-480 & G5 doser only.
-
Pulse Generator
111CA00
Can be plugged into the Select Doser and the Logger to simulate a water flow. Useful on exhibition stands and for fault diagnosis on-farms.
-
Reducing bush 1 1/4" to 3/4"
106CA91
For connecting T-piece to VTH25.
-
Reducing bush 2" to 3/4"
106CA92
For connecting T-piece to VTH40.
-
Reducing bush 3/4" to 3/8"
106CA90
For use connecting female injection assembly etc.
-
Replacement pump tube - Black
161CA08
Single black pump tube with 2 x connectors
-
Replacement pump tube - Blue
161CA16
Single blue pump tube with 2 x connectors
-
Replacement pump tube - Green
161CA32
Single green pump tube with 2 x connectors
-
Replacement pump tube - Green/Yellow
011CA32
Single green/yellow pump tube with 2 x connectors
-
Replacement pump tube - Grey
011CA63
Single grey pump tube with 2 connectors
-
Replacement pump tube - Orange
330CA20
Replacement pump tube - Orange. Single. For the Select 380.
-
Replacement pump tube - Purple
011CA48
Single purple pump tube with 2 connectors
-
Replacement pump tube - Red
161CA48
Single red pump tube with 2 x connectors
-
Replacement pump tubes - Black (10)
161CA08/REP
Pack of 10 black replacement pump tubes with 4 spare tube connectors.
For use with Select-480 doser.
-
Replacement pump tubes - Blue (10)
161CA16/REP
Pack of 10 blue replacement pump tubes with 4 spare tube connectors.
For use with Select-480 doser.
-
Replacement pump tubes - Green (10)
161CA32/REP
Pack of 10 green replacement tubes with 4 spare tube connectors.
For use with Select-480 doser.
-
Replacement pump tubes - Green/Yellow (5)
011CA32/R
Pack of 5 green/yellow replacement pump tubes with 2 x spare tube connectors.
-
Replacement pump tubes - Grey (5)
011CA63/REP
Pack of 5 grey replacement pump tubes including 2 spare tube connectors.
-
Replacement pump tubes - Purple (5)
011CA48/REP
Pack of 5 purple replacement pump tubes with 2 x spare tube connectors.
-
Replacement pump tubes - Red (10)
161CA48/REP
Pack of 10 red replacement pump tubes with 4 spare tube connectors
For use with Select-480 doser.
-
Replacement pump tube - White
330CA10
Replacement pump tube - White. Single. For the Select 380.
-
Screen
165CA21
Screen for Select dosers.
-
Screen & PCB
165CA04
Screen and printed circuit board for Select dosers.
-
Select 380 c/w power supply and both Orange and White (no sensor)
381CA00
Select-380 pump box c/w 12V 5A power supply, 6m delivery tube, both orange and white tubes and white and black roller assemblies, water meter connect, injection assembly, end weight, 3 connecting nuts and 3 blue ferrules. No flow sensor.
-
Select 388 c/w power supply and both Orange and White (no sensor)
388CA00
Select-388 pump box c/w 12V 5A power supply, 2 x 3m delivery tube, both orange and white tubes and white and black roller assemblies, water meter connect, 2 x injection assembly, 2 x end weight, 6 connecting nuts and 6 blue ferrules. No flow sensor.
-
Select 600 c/w power supply, no PCB
010CA81
Constant output pump without PCB based on Select-640.
-
Select-640 c/w battery clips & TBR10 sensor
010CA51
Same as 010CA50 EXCEPT battery clips in place of power supply.
-
Select-640 c/w battery clips & VTH25 sensor
010CA26
Same as 010CA25 EXCEPT battery clips in place of power supply.
-
Select-640 c/w battery clips & VTY10 sensor
010CA11
Same as 010CA10 EXCEPT battery clips in place of power supply.
-
Select-640 c/w power supply & TBR10 sensor
010CA50
Select-640 pump box 5A 12V power supply Delivery tube (3 m) with end weight Non-return valve Quick fit male/female injection assembly with white reducing bush 3/4" T-piece with 2 x white reducing bushes TBR10 flow sensor 2 x purple pump tubes with 2 connectors
-
Select-640 c/w power supply & VTH25 sensor
010CA25
Select-640 pump box 5A 12V power supply Delivery tube (3 m) with end weight Non-return valve Quick fit male/female injection assembly with white reducing bush 1 1/4" T-piece with 1 1/4" reducing bush VTH25 flow sensor 2 x purple pump tubes with 2 connectors
-
Select-640 c/w power supply & VTH40 sensor
010CA75
Select-640 pump box 5A 12V power supply Delivery tube (3 m) with end weight Non-return valve Quick fit male/female injection assembly with white reducing bush 2" T-piece with 2" reducing bush VTH40 flow sensor 2 x purple pump tubes with 2 connectors
-
Select-640 c/w power supply & VTY10 sensor
010CA10
Select-640 pump box 5A 12V power supply Delivery tube (3 m) with end weight Non-return valve Quick fit male/female injection assembly with white reducing bush 3/4" T-piece VTY10 flow sensor 2 x purple pump tube with 2 connectors
-
Select 640 pH-control
700CA50
Control box, selection of pump tubes, delivery tube, no electrode.
-
Select-640 Solo Plus c/w power supply (no sensor)
010CA80
Select-640 pump box 5A 12V power supply Delivery tube (3 m) with end weight Non-return valve Quick fit male/female injection assembly with white reducing bush 2 x purple pump tubes with 2 connectors
-
Select-640 Solo (pump box only)
010CA00
Select-640 pump box only
-
Select-640 SSD
010CA90
Select-640 Single Shot Doser complete with foot switch, 3m silicone delivery tube, 5A 12V DC power supply and instructions for use.
640 SSD Data Sheet (PDF) -
Select-G52 c/w control box & double G5 motor
362CA1#7
Large output G5 doser with double motor. Complete with 2 of each of 6m delivery tube, injection assembly with duckbill NRV, ferrules, locking nuts, inlet weights and pump tubes. Power supply & istructions for use also included. Flow sensor not included.
-
Select-G5 c/w AUS plug (no flow sensor)
360CA1#1-AUS
Includes high pressure pump and control box (both board mounted). Tube to be fitted indicated after 360CA - 1#7 is one pump head with tube #7 Also included are: 6m delivery tube, 12V power supply (AUS), injection assembly with duckbill NRV, ferrules, locking nuts, extra pump tube and inlet weight. Flow sensor not included.
-
Select-G5 c/w EU plug (no flow sensor)
360CA1#1-EU
Includes high pressure pump and control box (both board mounted). Tube to be fitted indicated after 360CA - 1#7 is one pump head with tube #7 Also included are: 6m delivery tube, 12V power supply (EU), injection assembly with duckbill NRV, ferrules, locking nuts, extra pump tube and inlet weight. Flow sensor not included.
-
Select-G5 c/w UK plug (no flow sensor)
360CA1#1-UK
Includes high pressure pump and control box (both board mounted). Tube to be fitted indicated after 360CA - 1#7 is one pump head with tube #7 Also included are: 6m delivery tube, 12V power supply (UK), injection assembly with duckbill NRV, ferrules, locking nuts, extra pump tube and inlet weight. Flow sensor not included.
-
Select-G5 c/w USA plug (no flow sensor)
360CA1#1-US
Includes high pressure pump and control box (both board mounted). Tube to be fitted indicated after 360CA - 1#7 is one pump head with tube #7 Also included are: 6m delivery tube, 12V power supply (US), injection assembly with duckbill NRV, ferrules, locking nuts, extra pump tube and inlet weight. Flow sensor not included.
-
Select Water Meter with VTH25 sensor
170CA25
Select Water Meter complete with power supply & VTH25 flow sensor
-
Select Water Meter with VTH40 sensor
170CA40
Select Water Meter complete with power supply & VTH40 flow sensor
-
Select Water Meter with VTY10 sensor
170CA10
Select Water Meter complete with power supply & VTY10 flow sensor
-
Sensor lead for VTH25/40
160CA88
Hall effect sensor lead for the VTH25 and VTH40 flow sensor.
-
Sensor wiring loom
163CA05
Sensor wiring loom complete with connectors fitted.
For use as a replacement inside Select doser.
-
Service Pack for the Select 380 (Orange)
310CA20
One black roller assembly and 2 orange replacement pump tubes for the Select 380.
-
Service Pack for the Select 380 (White)
310CA10
One white roller assembly and 2 white replacement pump tubes for the Select 380.
-
Signal out adaptor leads
166CA00
Adaptor leads to obtain one pulse out/l or gallon
-
Silicone pump tube (6.4mm bore) 3m length
012CA63
Silicone pump tube (6.4mm bore) (grey size) 3m length.
-
Spinstir 10-12 (100L) with follower & 12V power supply
212CA00
Spinstir 10-12 stirrer complete with 150 mm follower with maximum stock volume 100 litres. 12V power supply.
10-12 IFU (PDF) -
Spinstir 10-12 (100L) with follower & battery clips
212CA50
Spinstir 10-12 stirrer complete with 150 mm follower with maximum stock volume 100 litres. Battery clips.
10-12 IFU battery clips (PDF) -
Spinstir 10-12/15-12 replacement motor (12V)
165CA40
Replacement motor for both the Spinstir 10-12 and 15-12 (12V).
-
Spinstir 15-12 (200L) with follower & 12V power supply
213CA00
Spinstir 15-12 stirrer complete with 150 mm follower with maximum stock volume 200 litres. 12V power supply.
15-12 IFU (PDF) -
Spinstir 15-12 (200L) with follower & battery clips
213CA50
Spinstir 15-12 stirrer complete with 150 mm follower with maximum stock volume 200 litres. Battery clips.
15-12 IFU battery clips (PDF) -
Stirrer - 150mm follower
220CA15
Magnetic stirrer follower for use with the Spinstir 15-12 and 10-12.
-
Stirrer - 60mm follower
220CA60
Magnetic stirrer follower for use with Spinstir 6-240 and 612.
-
TBR10 flow sensor
160CA07
3/4" male threads
Flow 1 - 1200 l/hr
-
Threaded 1 1/4" T piece
106CA25
Threaded 1 1/4" T piece
For use with VTH25 sensors
-
Threaded 2" T-piece
106CA50
Threaded 2" T piece
For use with VTH40 sensors
-
Threaded 3/4" T piece
106CA00
Threaded 3/4" T piece.
For use with VTY10 and TBR flow sensors
-
Threaded insert for VTH25/VTH40
160CA89
Threaded insert only for VTH25/VTH40 flow sensor.
-
Tube connector - blue/black
167CA168
Acid resistant tube connector to blue and black pump tube.
-
Tube connector - green
167CA32
Acid resistant tube connector to green pump tube.
-
Tube connector - red/purple
167CA48
Acid resistant tube connector to red and purple pump tubes.
-
Tube end weight
152CA00
Tube end weight for 4.8mm id delivery tube
-
Turbine only for VTH25/VTH40
160CA87
Central turbine section as spare for VTH25/VTH40.
-
Viton black injection valve
015CA19
Alternate non-return injection assembly for dosers.
-
VTH25 flow sensor
160CA05
1 1/4" male threads at each end.
Flow 200 - 10000l/hr
-
VTH40 flow sensor
160CA08
2" male threads at each end.
Flow 400 - 25000 l/hr
-
VTH40 screen
160CA86
VTH40 screen and clip only.
-
VTY10 flow sensor
160CA03
3/4" male threads at each end with integral signal collector.
Flow 20 - 1500 l/hr
-
Water Meter Connect
166CA01
Connection cable to water meter.